How to JTAG a phat Xbox 360 COMPLETE GUIDE
- 6 years ago
Click settings and watch in HD!!!! Click on SHOW MORE to see full description:\r
\r
to buy your own!\r
\r
If you would like this service done for you, cont me weekendmodder@gmail.com to set up service!!!!!\r
\r
Link to known good soldering supplies on Amazon (I own and use every one of the items listed here): \r
\r
\r
\r
\r
Link to album containing all images referenced in this guide: \r
\r
Basic text guide to follow along with the video:\r
\r
1. Check your consoles dashboard version. It must be 7371 or below.\r
2. Check your consoles motherboard type. Xenons are done one way, non-Xenons are done a different way.\r
3. This set of instructions is valid for NON-XENON consoles only. That means it works on Opus/Falcon/Zephyr/Jasper boards only. \r
4. Solder in your connections to your JTAG header (NandX wires)\r
5. Test boot after soldering in the JTAG nand reading wires\r
6. Dump your nand (twice)\r
7. Confirm you have two MATCHING nand dumps - If your nand dumps are different DO NOT PROCEED.\r
8. Test boot after dumping your nand.\r
9. Build your Xell image and flash it to your console.\r
10. If you were to test boot at this point your console should not boot - this is because weve written Xell to the nand but not yet done the diode wiring.\r
11. Solder in your jumper wire\r
12. Solder in the first diode\r
13. Solder in the second diode\r
14. Power up your console, Xell should boot and you get your CPU key!\r
15. Plug the CPU key into J-runner and build your JTAG hacked image\r
16. Write the newly created hacked image back to the Xbox\r
17. Done! Now the power button or controller will now boot your hacked JTAG dashboard and booting with the Eject button will boot Xell
\r
to buy your own!\r
\r
If you would like this service done for you, cont me weekendmodder@gmail.com to set up service!!!!!\r
\r
Link to known good soldering supplies on Amazon (I own and use every one of the items listed here): \r
\r
\r
\r
\r
Link to album containing all images referenced in this guide: \r
\r
Basic text guide to follow along with the video:\r
\r
1. Check your consoles dashboard version. It must be 7371 or below.\r
2. Check your consoles motherboard type. Xenons are done one way, non-Xenons are done a different way.\r
3. This set of instructions is valid for NON-XENON consoles only. That means it works on Opus/Falcon/Zephyr/Jasper boards only. \r
4. Solder in your connections to your JTAG header (NandX wires)\r
5. Test boot after soldering in the JTAG nand reading wires\r
6. Dump your nand (twice)\r
7. Confirm you have two MATCHING nand dumps - If your nand dumps are different DO NOT PROCEED.\r
8. Test boot after dumping your nand.\r
9. Build your Xell image and flash it to your console.\r
10. If you were to test boot at this point your console should not boot - this is because weve written Xell to the nand but not yet done the diode wiring.\r
11. Solder in your jumper wire\r
12. Solder in the first diode\r
13. Solder in the second diode\r
14. Power up your console, Xell should boot and you get your CPU key!\r
15. Plug the CPU key into J-runner and build your JTAG hacked image\r
16. Write the newly created hacked image back to the Xbox\r
17. Done! Now the power button or controller will now boot your hacked JTAG dashboard and booting with the Eject button will boot Xell